Page 5 of 13
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:07 pm
by Sardon
Ok I've created a single wire which encompasses two pixels side by side as per below
- single-wire.jpg (220.15 KiB) Viewed 158536 times
- pixels.jpg (1.92 KiB) Viewed 158536 times
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:09 pm
by Pogo
Some screen shots on the way shortly...
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:30 pm
by Pogo
OK. Basic clone trigger setting establishing re-trigger time and alert/trigger duration time. The particular setting will allow 6 minutes (240 secs) worth of continuous triggers to be combined into a single clip if wanting to actually record the triggered activity as motion recordings vs only jpegs for phone alerts.
- Honic Clone Trigger 1.jpg (91.84 KiB) Viewed 158753 times
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:34 pm
by Sardon
These are my settings do you think they would have posed a problem?
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:38 pm
by Pogo
Next are the basic sensor settings to be applied to a given zone... (I'll spare you the zone setting since you aready have that established.)
- Honic Clone Motion Sensor.jpg (89.16 KiB) Viewed 158707 times
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:39 pm
by Sardon
Well.. I've just walked back and forth across the balcony and yet still no form of alert... I have disabled motion detection but have left zone enabled with the newly created wire... Very bizarre that it isn't working.
In addition my settings are set to the most sensitive which should result in some form of motion detection.
Min Obj. size 1
Min. Contrast 20
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 3:49 pm
by Pogo
Sardon wrote: ↑Fri Jan 12, 2024 3:34 pm
These are my settings do you think they would have posed a problem?
Use my examples for now.
Next comes the Record settings. This example provides for .jpegs only for SMS alerts. Enable video recording if it is also desired based upon the same triggers as the alert or to simply experiment with your settings.
(BTW, I'm having some difficulty with the forum allowing successive posts, hence some delay in my responses.)
- Honic Clone Record.jpg (109.61 KiB) Viewed 158558 times
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 4:03 pm
by Pogo
Now set the alert and enable the desired action...
- Honic Clone Alert.jpg (98.37 KiB) Viewed 158530 times
- Create and Enable Alert Action.jpg (70.03 KiB) Viewed 158530 times
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 4:04 pm
by Sardon
Ahh well my record tab on the clone was still set to capture continuous video which is probably a no no considering the main camera is currently allocated to do this.
Current clone record tab settings
Re: Seeking Assistance with Eliminating False Positives in Motion Detection
Posted: Fri Jan 12, 2024 4:11 pm
by Pogo
The settings I provided should be a good starting point to refine your overall setup.
There is a lot to actually unpack there and enormous flexibility to customize anything and everything but it should do exactly what you are intending to accomplish.
I need to break away again for a bit, but report back as you go.
Tweak as you like and don't hesitate to ask additional questions.