BI 5.0.0.61 dead

[eboggs_jkvl]

Does that help?

[Tinman]

Well I was hoping it would tell more, but be sure to send that to BI support as well....hopefully they will be releasing a new update soon for you. Apparently the 5.0.0.61 update changed something in the registry as well as the blueiris.exe. It is always a good idea to have both backed up as sometimes you need to restore the registry as well. You MIGHT be able to do a system restore to a point before you updated to 5.0.0.61....if you can be sure to run the 5.0.0.xx earlier update before you try running BI or the 5.0.0.61 will just re populate the registry again. First see if you can do a system restore...I have all the updates and can give you a link to any you want. I will check back later.

try the new 5.0.0.63 works for me...just dl it from the website and run the update manually.

[cohental]

I have the same thing...
Reverted back to an older version.

[Tinman]

Also you can manually disable your cameras by editing the registry. Click Start\run\regedit just right click the entry and change the value to 0 to disable cam. By trial and error you can find which cam is the culprit. If you don't have too many cams just disable all of them and then see if BI will run. This is kind of a last thing to try if BI continues to crash.

Annotation 2019-07-16 210522.jpg (87.28 KiB) Viewed 9247 times

[reddawg]

Updating to Blue Iris 5.0.0.63 x64 still causes blueiris.exe to crash immediately.

V5.0.0.57 x64 - Good
V5.0.0.58 x64 - Good
V5.0.0.59 x64 - Good
V5.0.0.61 x64 - CRASHES
V5.0.0.62 x64 - CRASHES
V5.0.0.63 x64 - CRASHES

BI5.0.0.63 Crash.png (20.02 KiB) Viewed 9246 times

[Tinman]

I noticed for some reason it changed to of my cams to the wrong model by updating to 5.0.0.63. In my case it did not cause it to crash, but I have seen a bad cam configuration crash the app. Maybe you can see what it changed by looking at registry.

[eboggs_jkvl]

Ok, you are taking me out of my turf by messing around in the registry. I'm 75 and not bad at this but I do have my limitations!

I loaded .63 last night and it still took me multiple clicks to get the BI5 to run.

There was a link earlier to a "working" version of BI5. I'm going to use it and see if I can get running again.


As I have it running at the moment, I'll look in and see if it changed any of my cameras but this will be a PITA to do.

Elmer

[eboggs_jkvl]

I did not see any changes in the camera types listed in BI5. If it made changes to my registry, I have no clue.

[eboggs_jkvl]

Also you can manually disable your cameras by editing the registry. Click Start\run\regedit just right click the entry and change the value to 0 to disable cam. By trial and error you can find which cam is the culprit. If you don't have too many cams just disable all of them and then see if BI will run. This is kind of a last thing to try if BI continues to crash.

Annotation 2019-07-16 210522.jpg

Would a disable of the cameras in BI accomplish the same thing as the disable in the registry?

[eboggs_jkvl]

I disabled all of my cameras in BI5. Closed it and 1 clicked it back open. I enabled a camera each time and it 1 clicked open. I only have 6 cameras so this didn't take long. I enabled all of my cameras eventually and it 1 clicked open. OK! I figured that it might be working!

Rebooted the PC with all of the cameras enabled and it did not open after the boot up. I started clicking on the icon and got BI5 to run after 6 clicks.


SIGH...........


Still broke.