Search found 1104 matches
- Wed Jan 29, 2020 6:17 am
- Forum: Blue Iris 5
- Topic: Test Run Video Through Motion Detector not triggering
- Replies: 6
- Views: 7251
Re: Test Run Video Through Motion Detector not triggering
You'll need to start playing the video about 10 seconds before the event to trigger. If your recording Continuous, then all you need to do is play the clip, stop, go back 10 seconds, then play. Or increasing the 'Pre trigger video buffer' to 12-15 seconds will make it as easy as just playing the cli...
- Wed Jan 29, 2020 6:06 am
- Forum: Blue Iris 5
- Topic: Object Crossing Zones A-B vs AB
- Replies: 3
- Views: 4205
Re: Object Crossing Zones A-B vs AB
... For example, is there a time period in which these events must occur? Is there a "cool down" time that applies, after which the initial trigger is reset, or...?? Yes, Make Time & Break Time. For example, in the " A-B " scenario, could an object exist in zone A for an hou...
- Wed Jan 29, 2020 5:58 am
- Forum: Blue Iris 5
- Topic: Object Crossing Zones A-B vs AB
- Replies: 3
- Views: 4205
Re: Object Crossing Zones A-B vs AB
Hi, Can anyone explain the difference between zone crossing triggers; AB and A-B ? ... Essentially, your correct. AB would be about the same as A-B or A>B, A<B However, lets say you have a third zone... C. They are lined up, A B C left to right. AB-C would mean that motion would need to be detected...
- Wed Jan 29, 2020 5:48 am
- Forum: General discussion
- Topic: Motion based search capability?
- Replies: 11
- Views: 11341
Re: Motion based search capability?
If your want to search through existing BI recordings, yes. It's called 'Test run video thru motion detector'. Not easy to use, but it does work. Just remember to save your camera settings first, so you can restore if you don;t like the new settings.
- Wed Jan 29, 2020 5:38 am
- Forum: Blue Iris 5
- Topic: OOps - Need a Clean Start - How ?
- Replies: 9
- Views: 8590
Re: OOps - Need a Clean Start - How ?
Also, you can export the Registration info, then, delete the entire branch, re install BI. Before starting it the first time, Double click the .reg file you saved to enter the registration info it back into the registry. This way, you don't have to enter it manually. I've used this a few times. HKEY...
- Wed Jan 29, 2020 5:29 am
- Forum: Blue Iris 5
- Topic: switching between cameras while using timeline view?
- Replies: 12
- Views: 13595
Re: switching between cameras while using timeline view?
I'm assuming your zoomed into one camera? (Full window) There are 2 views in the timeline, View (non-edit), and, Edit. You must make sure your in 'View (Non-edit)' mode to switch cameras while viewing in the timeline. View Mode (Non-edit): White boarder around camera. Nothing between the bottom of t...
- Tue Jan 28, 2020 8:37 am
- Forum: General discussion
- Topic: New user multi cam multi location
- Replies: 6
- Views: 6492
Re: New user multi cam multi location
... I've switched to AnyDesk. But, it requires the remote computer to acknowledge and approve the connection. Whereas with TeamViewer, you can set it up for unattended access. CORRECTION... AnyDesk does have 'Unattended Access', and I have successfully configured it with a password on a remote desk...
- Tue Jan 28, 2020 6:29 am
- Forum: Blue Iris 5
- Topic: Disable Webcasting by Group?
- Replies: 0
- Views: 2182
Disable Webcasting by Group?
According to the BI Help, in the Webcasting section, it states... Consider disabling webcasting of the “all cameras” group altogether. But, does not say how to do this. I cannot find any 'group' webcast setting. Other than disabling 'Webcast' per camera (which would also disable Webcasting in all gr...
- Tue Jan 28, 2020 6:00 am
- Forum: Blue Iris 5
- Topic: Force to a preset after starting BI
- Replies: 4
- Views: 4446
Re: Force to a preset after starting BI
Turns out there is a way to do it. This is the response I received from support: Force to a preset after starting BI "Yes this is possible ... please see the Events button/page from the Schedule tab in camera settings. Add a preset event at anytime of the day using the "search back" ...
- Mon Jan 27, 2020 10:16 pm
- Forum: Blue Iris 5
- Topic: Stored clips not listed
- Replies: 3
- Views: 2942
Re: Stored clips not listed
- How many cameras do you have.
- How many cameras is this happening too?
- Can you post a screenshot of the BI settings 'Clips and arching' for New and Storage.
- Can you post a screenshot of the camera(s) 'Settings/Record'.
- How many cameras is this happening too?
- Can you post a screenshot of the BI settings 'Clips and arching' for New and Storage.
- Can you post a screenshot of the camera(s) 'Settings/Record'.